Please be aware there is a Chinese company that has cheaply copied OUR Registered design for these brackets and is
selling them From China but they are NOT the same. The Chinese copy of this brake bracket is very cheap pig iron
that is brittle and breaks within 30---40 brake lever presses.
--------- IF you buy here you get the MADE in USA original bracket made from #8 hardened steel that is
warrantied for life against breaking or bending when properly installed.
Also, ours ship out within 5--10 hours of your order and ship from within the USA.
----The cheap Chinese copy is Dangerous, and they are shipping from China, we have tested them.
----Bracket Fits on 99% of bicycle frames Front or rear ! -----FOR E Bikes please file out the fork inside to make it wider for E-bike axles.
----For frames with no disc brake Tabs NOW you have tabs ------ Make sure you use the rubber tape we give you if the clamp is too big for your tubing !
Please measure your bike frame tubing at 2 inches above your wheel axle ! Use a caliper measuring device for accurate thickness of frame tubing !
----Now you can have Disc Brakes on almost any bike ------- ( sometimes you need to make adjustments if you have square tubing on your frame )
----BIG size is for front shocks(or forks) that are 0.9\" ----1.22\" thickness. If your front forks are OVER 0.9\"thick (like 1.20\")
then you NEED our BIG 1.22\" clamps ( They adjust 0.9\"---1.22\")----( we do have a few brackets that will fit up to 1.30\" thick tubing -----
order the BIG size and sends us a message that you need 1.30 thickness !)
Thickness MEANS DIAMETER Please measure carefully. So Choose BIG for front forks over 0.9\" thick.
------ XL size for front forks (or shocks) that have tubing near axle that is 1.33\"----1.50\" thick (this is very rare !)---
For Rear brakes almost ALL bikes will use the Regular size!(1/2\"--7/8\" thick frame tubing) because the rear tubing is very thin on bike frames.
---please tell us what disc size you are using There are only 4 disc sizes 140mm (very rare) ----160mm (very common) ----180mm and 203 mm(8 inch disc).
For about 90% of all brakes the 180mm brackets we sell will also work on the 203 mm rotors !
------ If you have 203 mm rotors just order the 180 mm bracket !
If we know your disc Rotor size then we can double check and make sure it will work on your bike !
--- Our REG. size is 1/2\"----7/8\" thickness of frame tubing. All rear brakes will use this size.
The other size is BIG 0.9\"-----1.22\" thickness. The only reason we repeated this size twice is because is has 2 diff. applications.
One bracket is for front shocks (usually 1.1\"----1.22\" thick) OR for BMX or beach cruisers with those really fat forks which CAN be
anywhere from 1.0\" thick to 1.33\"thick. BUT normal front forks are just 1/2\"----7/8\" thick so they use the REGULAR size (1/2\"-7/8\").
It\'s really simple ! Is the frame tube on your fork thicker than 1.0\" or thinner ? Is it thicker than 1.22\" or between 1.00\"----1.22\" (BIG size.)
Specially made in USA for use on e-bikes and all bikes. Now everyone can have disk brakes. For E bike axles you need to file the fork area of the bracket to fit on thicker e-bike axles.
very thick front forks (over 0.9\" thick). Only BMX bikes and cruisers etc... have these thick forks Most shocks are 1.20\" inch
thick so they need the BIG bracket. Just order this item and tell us you need the BIG size bracket !
We use HEAVY DUTY USA 1/5\" thick #8 Hardened steel ( after all sanding and finishing they are 0.19 \" thick)
Don\'t Buy those cheap Chinese copies of our bracket because they use
very soft iron and do break easy.
Be Safe ! Buy USA.
Fast shipping !
