UBB Store

Body Armor Curved Two 10x12 Level III 3 DOD Certified Plate MIL-DTL-46100
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Body Armor Curved Two 10x12 Level III 3 DOD Certified Plate MIL-DTL-46100
Price: US $105.27

Please check out my store for a full line of Powdercoatedplates! (VRaptor ArmorWorks LLC)
This sale is for Two 10\" x 12\" Brand New, Level III Armor Plates!Both plates are CURVED! These plates are cut from 1/4\"Certified Level III Mil-Spec MIL-DTL-46100 Armor Plate.Yes....this is the exact same material that our Military purchases to armor tanks, personnel carriersand Humvees!Both plates feature our Comfort Cut profile with symmetrical cuts on both sides of the plates. Both plates have had all edges and corners rounded so they don\'t cut away at your plate carrier, and both plates have beenPowdercoatedto prevent rust and corrosion. These are Stand-Alone plates cut fromCertified Level III Mil-Spec MIL-DTL-46100 Armor Plate!....which has been tested to Military Specs and been proven on the battlefield, over and over.Copies of the DOD certs/ballistic test sheets are shipped with every order. Unlike other armor products, these plates have NO EXPIRATION DATE. Ceramic and polymer based armor has a limited shelf life, after which, you\'ll have to spend your money all over again for new plates. They can also be fragile/brittle and break if dropped or take an impact. With our MIL-DTL-46100 armor plates, you can pass them down to your great grandchildren....or run them over with a dump truck and pick them up and use them!This is NOT AR500 or HY-100. Do your homework! Look up AR500 and HY100 and you will find that the \"AR\" in AR500 stands for ABRASION RESISTANT!! Yes, you read that right. AR500 was developed to be used in high abrasion applications like back-hoe buckets, snow plow blades and farm equipment (plow and disc blades). HY100 was designed by the Navy to build ship hulls out of. MIL-DTL-46100 was specifically designed from the start by THE DEPARTMENT OF DEFENSE to be used as Ballistic Armor Plate! This is the best of the best armor platethat you can buy.You will not find another set of armor plates on with all of these features!
We realize that you have many sellers and options to choose from when purchasing armor. If you\'re looking for \"cheap\" armor, there are plenty of choices out there for you. Sheets of AR500 are HALF the price of MIL-DTL-46100. Yes...MIL-DTL-46100 is double the price per sheet. With all of the competition on , if you\'ve been following along, you know that many of the sellers have significantly dropped their prices over the past few months to stay competitive with each other. Our goal is not to manufacture cheap armor for the cheapest cost and turn around and sell it for the biggest profit we can get. Our goal at VRaptor ArmorWorks is to manufacture the very best armor you can buy ANYWHERE and sell it for the best price we can offer. A quick look thru some of the other offerings here on , it\'s pretty easy to see how the \"others\" can offer armor for sale here that is well under OUR COST to manufacture \"similar\" plates. Cheap steel, cheap manufacturing processes and cheap coatings. You have to ask yourself.....if AR500 is just as good as MIL-DTL-46100 and half the price, why doesn\'t our military use AR500 as ballistic armor? When choosing ammo to load into your concealed carry gun, are you going to choose Wolf or Brown Bear.....or Hornady or Federal? Are you going to load that ammo into a Jennings or Hi-Point.....or a Glock or Sig? You know the saying.....\"You get what you pay for.\"
Plates are IN STOCK and ready to ship! If you look at our response, you will see that we have a long record of fast shipping with over 90% of our orders going out either same or next business day, depending on what time the order comes in.We have many other armorsets listed here on . Simply click the \"See all items from this seller\" link above.
These plates are 100% made in America. The steel is 100% manufactured in the USA. The plates are cut on a CNC Plasma cutter with water table built by me, right here in the USA. Plates are processed and coated right here in the USA. Other sellers here on would have you believe that laser cutting is superior to plasma cutting for these plates. If you read their false claim, they actually contradict themselves....first telling you that plasma cutting will make the plate brittle and it will shatter (steel is too hard)...and then immediately after that, telling you that it will make the edge soft....which means that the bullet would penetrate the steel...not shatter it. Well, the proof is in the photo of the test plate above. It successfully defeated a high-power rifle round right on the very edge of the plate.These plates have been thoroughly de-greased, cleaned andpowdercoated to prevent rust and corrosion.Color will be the same or very similar to the photos. Both front and rear plates have been curved and feature our exclusive \"Comfort Cut\" profile which provides extra clearance for right (or left) shoulder movement for shouldering a rifle properly, as well as all corners rounded so that you do not have sharp 90 degree corners poking you or wearing holes in the plate carrier. All edges have also been sanded/beveled/rounded off so there are no sharp edges to cut or wear away at the plate carrier. For those of youwho arenot familiar with what powdercoating is, it is an extremelydurable and abrasion resistant coating.Basically, the plates are electro-statically coated with a layer of powdered plastic and then placed in an oven which melts to plastic powder to the surface of the plates. It is far superior to any paint.If you have concerns about these plates going thru thisprocess....well, the proof is in the photos above. It is a low temperature process that does not even come remotely close to the heat that would be required to affect the physical properties or strengthof the steel.As you can see from the photo, the plate was tested against 5.56 62gr JHP @ 35yrds, 5.56 Steel-core \"Penetrator\" rounds @ 35yrds, 5.56 55gr FMJ @35yrds, .223 55gr JHP @35yrds, 12ga 1.25oz Mangumslug @ 15yrds,.308 Win145gr FMJ@ 40yds and .308 Win145gr FMJ@ 15yrds!!These plates are multi-hit capable (as you can see from the test plate!). As you can see from the DOD test sheet in the photos above, the Department of the Army Ballistic Test Certificate shows the test results of this material with \"CAL30APM2\" projectiles (a .30 cal/7.62 caliber Armor Piercing bullet) with the velocity listed and \"pass\" test result. Yes, this stuff is the real deal! They are cut on a CNC Plasma Water Table to keep the plate cool during cutting. As you can see from the test plate, it has been hit with a 5.56 round right at the very bottom edge of the plate, confirming that the strength of the plate\'s edge has not been compromised. You are not going to get any closer to the edge of the plate than this!! My competition would have you believe that the powdercoating process somehow weakens the steel, which is why I specifically POWDERCOATED THE TEST PANEL in the photos above BEFORE testing it against rifle fire to prove once and for all that the powdercoating process has no effect on the ability of the steel to stop rifle rounds and has no effect on it\'s strength. Period.
Here is a message I received from one of my customers:
I just got my plates today and am super stoked with the quality of craftsmanship and materials used. I shot one of the side plates with 75 grain fmj 5.56, steel core penetrator in 5.56, 7.62x54r and .243. it stopped all rounds with minimal damage to the plate. ( the big rifles did make some pock marks or denting but the plates defeated the rounds) I cannot express how happy I am with the product and will be sending my ex-military buddies your way for plates. Keep up the good work; you\'re definitely on the right side of things.
thanks again,
-Shawn
If you are looking for a plate size that we don\'t carry, please let us know what size/cut profile you would like to see us keep in stock. If we get enough people looking for the same size plates, we would be glad to start stocking that size. We cut these plates in-house, so we can cut whatever size or shape is desired. Just scroll down to the \"Ask a question\" box and let us know.
The 10x12 plates each weigh in at 7.59 lbs. At VRaptor ArmorWorks, LLC, we believevery stronglyin the 2nd Amendment and the Rights of the People to Keep and Bear Arms.Unfortunately, there is a current political climate that wishes to destroy our 2nd Amendment rights under the Constitution of the United States of America. VRaptor ArmorWorks, LLC does not support ANY infringements on our rights as outlined in the 2nd Amendment. These plates areproudlyMade in theUSA!VRaptor ArmorWorks, LLCwill only sell ourCertified armor to law-aoffering adults who have no felony convictions, and are not involved with criminal organizations. Residents of Connecticut are prohibited from buying Body Armor online. We will only ship to states where Body Armor is allowed, please know your local and federal laws prior to purchasing.No shippingoutside of the USA. By purchasing you agree to this and all terms listed on this page. In addition, YOU are responsible to ensure that your ballistic panels are properly inserted and installed. We are not responsible for any injury or death as a result of the use or misuse of this product.No armor is \"bullet-proof\". I am selling this armor at a reasonable and affordableprice, EVEN THOUGH THE MATERIAL IS EXTREMELY EXPENSIVE TOPURCHASE! My main purpose of selling this armor is to provide armor to people who might otherwise not be able to affordit, and I do believe thatEVERY law-aoffering American has the right to personal protection.There is noguarantee that every plateI sell will stopany rifle round at any distance.I will not be held responsible for any injuries or death that would result from the use, mis-use or failure of the plates themselves.



Buy Now

Related Items