DSLRKIT MID8P1U Passive PoE Injector Switch
9Ports (1Uplink,8 PoE) 10/100Mbps
Midspan Mode-B Unsolicited Power(4,5+/7,8-)
Compatible IEEE 802.3af/at, Per port Max 50Watt
Suitable for Hikvision,DAHUA andother brands with 802.3af/802.3at PoE Powered Devices(PD)
This is an Passive Power Over Ethernet of9 port 10 / 100Mbps-T Ethernet switches, including8 unsolicited PoE Ethernet ports and 1 Uplink ports. With an external 110V-240VAC to 48VDC power supply adapter, any one of the8 port can provide output power, each Ethernet port can provide network transmission speeds of up to 10 / 100Mbps , with Cat5 / 5e / 6 network cable.
Which compatible with IEEE 802.3af/at Mode-B(4,5+/7,8-) POE switch device, but it does NOT include the 802.3af/at compliant detection feature. It supplies power NO MATTER WHAT, so don't plug the "Power Link 1~8" side into anything that isn't ready for it.
This POE switch only support 10/100M connection, PoE ports do not support Gigabit ethernet connection, because "Power Link 1~8" port using 4,5,7,8 pin as power transfer, Please do not connect any "NONE PoE gigabit ethernet device and Uplink device" on "Power Link 1~8" port, this will damage your device.
devicePlease do not access "Power Link port" this will damage your device.
Compatible all802.3af/at device as Wireless Access Point, IP Phone, IP camera, Gateway , Switch, or More.....
If your camera is with word “12V/PoE” as this picture shows, then please select this 52V PoE Switch, do not select 12V PoE Switch.
Because "12V/PoE" means it can offer power supply to camera via 12V DC port or 48V(or 52V) PoE Ethernet port.
- 9x 10/100Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 8-Ports PoE function
- Midspan Mode-B Unsolicited Power(4,5+/7,8-)
- Supports PoE power up to 120W for all PoE ports, Per port Max 48V 1A or 50Watt
- Supports PoE IEEE802.3af/at compliant Powered Device (PD)
- Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
- Full/half duplex transfer mode for each port.
Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with4 pairs UTP Cat5/5e/6 cable。
any supported IEEE802.3af/at Powered Device and unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs)
LED ON: power on. LED OUT: power off
Yellow Light LINK/ACT
LED ON Indicates the port is connected to a network device and has been started
LED OFF Indicates that this port is not connected to a network device or has not been started
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3x Full-Duplex flow control
Data Transfer Rate
Ethernet: 10Mbps (Half Duplex)，20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex) ，200Mbps (Full Duplex)
10Base-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)
100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)
PoE Power on RJ45
Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8
DC Output: 48V, Per port Max 1A or 50Watt, 4 POE ports Total 3A(Max. 140Watt)
Number of Ports
9x 10/100Mbps Auto-Negotiation RJ45 ports with8 PoE enabled (port-1~ port-8)
AC Power Adapter
AC Input: 110V ~ 240VAC, 50Hz ~ 60Hz.
DC OutPut: 48V/3A
3.2Watts (max. no PD connected)
According to the actual power consumption of equipment
Operation Temperature:0 ~40℃ (32 ~104℉ )
Storage Temperature: -40 ~70℃(-40 ~158℉)
Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing
197mm W x 73mm D x 32mm H
RAM Register Capacity
64K bytes per device
MAC Address List
1K entries per device
Frame Forward Rate
10Mbps Ethernet: 14880pps/Port
100Mbps Ethernet: 14880pps/Port
AC power plug is US or EU type,if you need other type (AU or UK),Please leave a message.
12 Months Warranty from the date of purchase.