Folger Tech Kossel 2020 3D Printer (Full Kit) REV B
**Assemblyrequired

** As wereceivecustomer response we do make small alterations to the kit if we feel they improve the kits performance and stability, the kit youreceivemightreflectsome of these slight changes and improvements.

If you are looking for a fun and exciting 3D printer to build that requires a bit more technical skill than our i3 kit this delta printer might be just what you are looking for. This delta style printer is constructed using 2020 extruded aluminum rails making it strong as well asaestheticallypleasing. This printer also comes with an auto level servo that will set a relative bed level without you making the physical adjustments to the bed. All in all this is a great kit and worth the time required for this slightly more demanding setup.

This kit includes the following:

• Complete Set of Black Printed Plastic Parts Needed

• Aluminum corners

• Pre-Cut2020 Aluminum Beam ( x3-700mm x9-300mm)

• 1x Bearings Set

• Nylon Sliders Wheels

• Aluminum Heated Bed (3mm x 210mm)

• x3 End Stop Circuits w/ LED (Incl. 40" Cables)

• x3 BeltTension Springs

• CarbonFiber Rods (Need to Be Cut to Length)

• x12 Tie Rod Ends

• DirectDrive Extruder w/ Injection Molded Part (For 1.75mm ABS/PLA) MK9 TYPE

• x1 All-Metal Hot End for 1.75mm Filament

• All Required Nuts/Bolts for Assembly

• 360W12V 30A Power supply

• x4 NEMA 17 Stepper Motors

• 5 Meters of GT2 Timing Belt

• x3 20 Tooth Pulleys

• x1 RAMPS1.4 Controller

• x1 ArduinoMega 2560 R3 Clone

• x5 A4988 Stepper Drivers (1 Extra)

• x1 Roll 8mmKapton Tape

• x1 Inductive Sensor with resistors

• Wiring Set

• Power Cable

Features:

• 210mmPrint Area x 310mm

• Canprint ABS or PLA 1.75mm

• Canrun 110V or 220V (Only Comes With US cord)

• Packed And Shipped from the USA

Items you will need:

• Tools

• Filament

• Time

Build Guide and Firmware/Software:** Please note the items included inside the below link are often updated to include new and updated information so please bookmark it for your records. Link also contains .stl files to print replacement plastics.

• Google Drive items you might be interested in buying with your kit:
  • 2004 LCD Controller w/ SD Card Reader (Print Without a Computer!):2004 LCD w/ SD Card Reader
  • Filament ABS/PLA: 1.75 ABS & PLA Filament (Various is a kit of components for assembly into a 3D Printer by the end user. Building and using the printer is potentially very dangerous as it involves electricity and high temperatures.
    Building the printer will require a certain amount of physical dexterity, common sense and a thorough understanding of what you are doing. We have provided fully comprehensive build documentation to enable you to build your Folger Techl 3D Printer Kit in a safe manner.
    
    However ultimately we cannot be responsible for your health and safety whilst building or operating the printer, with that in mind be sure you are confident with what you are doing prior to commencing with building or buying. Read all of the manual to enable you to make an informed decision.
    
    Building and operating involves electricity, so all necessary precautions should be taken and adhered to, the printer runs on 12V supplied by a certified power supply, so you shouldn't ever have to get involved with anything over 12V but bear in mind there can still be high currents involved and even at 12V they shouldn't be taken lightly.
    
    High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end runs at 230°C, the heated bed runs a 110°C and the molten plastic extruded will initially be at around 200°C, so special care and attention should be made when handling these parts of the printer during operation.
    
    We wouldn't recommend leaving your printer running un attended, or at least until you are confident to do so. We cannot be held responsible for any loss, damage, threat, hurt or other negligent result from either building or using the printer.
    Track Page Views With
    Auctiva's FREE Counter