Outback Flexmax 80 FM80 MPPT 80 AMP Solar Charge Controller Outback Power Systems
FLEXmax 80 MPPT Charge Controller
The FLEXmax 80 is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Systems. The FLEXmax 80’s innovative MPPT algorithm is both continuous and active, increasing your renewable energy yield up to 30%. Thanks to enhanced cooling, the FLEXmax 80 can operate at its full 80 amp maximum current rating in ambient temperatures as high as 104°F (40°C).
Included in the FLEXmax 80 are all of the features first developed by OutBack Power in the revolutionary MX60, such as support for a wide range of nominal battery voltages and the ability to step-down a high voltage solar array to recharge a low voltage battery. A built-in backlit display shows status information at the touch of a button. Enhanced network communications allow the FLEXmax 80 to be remotely programmed via the optional MATE system display and controller.
The new FLEXmax 80 is the only choice when you demand a high performance, efficient and customizable charge controller for your advanced power PV Array Output by up to 30%
Advanced Continuous Maximum Power Point Tracking Algorithm Full Output Capacity in Ambient Temperatures up to 104°F (40°C) Battery Voltages from 12 VDC to 60 VDC Automatic Battery Voltage Detection at Start Up Fully OutBack Network Integrated and Programmable Programmable Auxiliary Control Output Negative or Positive Ground System Capable Built-in 128 days of Data LoggingFLEXmax™ 80 Specifications* Nominal Battery Voltages12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up) Maximum Output Current 80 amps @ 104° F (40°C) with adjustable current limit Maximum Solar Array STC Nameplate 12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC Systems 7500 Watts NEC Recommended Solar Array STC Nameplate 12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts PV Open Circuit Voltage (VOC) 150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum Standby Power Consumption Less than 1 Watt typical Power Conversion Efficiency 97.5% @ 80 Amps in a 48 VDC System - Typical Charging Regulation Five Stages: Bulk, Absorption, Float, Silent and Equalization Voltage Regulation Set points 10 to 80 VDC user adjustable with password protection Equalization Charging Programmable Voltage Setpoint and Duration - Automatic Termination when completed Battery Temperature Compensation Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell Voltage Step-Down Capability Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input Programmable Auxilary Control Output 12 VDC output signal which can be programmed for different control applications (Maximum of 0.2 amps DC) Status Display 3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total Remote Display and Controller
Optional Mate or Mate2 with RS232 Serial Communications Port
Network Cabeling Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires) Data Logging Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production Hydro Turbine Applications Consult factory for approved Turbines Positive Ground Applications Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications) Operating Temperature Range Minimum -40° to maximum 60° C (Power capacity of the controller is automatically derated when operated above 40° C) Environmental Rating Indoor Type 1 Physical Specifications Conduit Knockouts One 1" (35mm)on the back; One1" (35mm) on the left side; Two 1" (35mm) on the bottom Warranty Standard 5 year Weight - Unit, 12.20 lbs (5.56 kg) - Shipping, 15.75 lbs (7.10 kg) Dimensions - Unit 16.25" x 5.75" x 4" (41.3 x 14 x 10 cm) - (H x W x D) - Shipping 21" x 10.5" x 9.75" (53 x 27 x 25 cm) Options Remote Temperature Sensor (RTS), HUB 4, HUB 10, MATE, MATE 2 Menu Languages English & Spanish
OutBack Power provides a five (5) year limited warranty againstdefects in materials and workmanship, and a two (2) year limitedwarranty against fan failure
Use appropriate wire size in accordance with NEC.
* Specifications subject to change without notice.
Hurricane Wind Power
2019Corporate America Today2019 Best Off-GridRenewable EnergyProduct Supplier - USAUP TO 50% DISCOUNTSTOP accept payment by any of the following pay as soon as possible after winning an sale, as that will allow us to post your item to you sooner!
We offer Fast shipping on all orders!
Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 14 days from the date you purchased it.
Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.
FLEXmax 80
MPPT Charge Controller
The FLEXmax 80 is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Systems. The FLEXmax 80’s innovative MPPT algorithm is both continuous and active, increasing your renewable energy yield up to 30%. Thanks to enhanced cooling, the FLEXmax 80 can operate at its full 80 amp maximum current rating in ambient temperatures as high as 104°F (40°C).
Included in the FLEXmax 80 are all of the features first developed by OutBack Power in the revolutionary MX60, such as support for a wide range of nominal battery voltages and the ability to step-down a high voltage solar array to recharge a low voltage battery. A built-in backlit display shows status information at the touch of a button. Enhanced network communications allow the FLEXmax 80 to be remotely programmed via the optional MATE system display and controller.
The new FLEXmax 80 is the only choice when you demand a high performance, efficient and customizable charge controller for your advanced power PV Array Output by up to 30%
Advanced Continuous Maximum Power Point Tracking Algorithm Full Output Capacity in Ambient Temperatures up to 104°F (40°C) Battery Voltages from 12 VDC to 60 VDC Automatic Battery Voltage Detection at Start Up Fully OutBack Network Integrated and Programmable Programmable Auxiliary Control Output Negative or Positive Ground System Capable Built-in 128 days of Data LoggingFLEXmax™ 80 Specifications* Nominal Battery Voltages12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up) Maximum Output Current 80 amps @ 104° F (40°C) with adjustable current limit Maximum Solar Array STC Nameplate 12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC Systems 7500 Watts NEC Recommended Solar Array STC Nameplate 12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts PV Open Circuit Voltage (VOC) 150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum Standby Power Consumption Less than 1 Watt typical Power Conversion Efficiency 97.5% @ 80 Amps in a 48 VDC System - Typical Charging Regulation Five Stages: Bulk, Absorption, Float, Silent and Equalization Voltage Regulation Set points 10 to 80 VDC user adjustable with password protection Equalization Charging Programmable Voltage Setpoint and Duration - Automatic Termination when completed Battery Temperature Compensation Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell Voltage Step-Down Capability Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input Programmable Auxilary Control Output 12 VDC output signal which can be programmed for different control applications (Maximum of 0.2 amps DC) Status Display 3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total Remote Display and Controller
Optional Mate or Mate2 with RS232 Serial Communications Port
Network Cabeling Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires) Data Logging Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production Hydro Turbine Applications Consult factory for approved Turbines Positive Ground Applications Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications) Operating Temperature Range Minimum -40° to maximum 60° C (Power capacity of the controller is automatically derated when operated above 40° C) Environmental Rating Indoor Type 1 Physical Specifications Conduit Knockouts One 1" (35mm)on the back; One1" (35mm) on the left side; Two 1" (35mm) on the bottom Warranty Standard 5 year Weight - Unit, 12.20 lbs (5.56 kg) - Shipping, 15.75 lbs (7.10 kg) Dimensions - Unit 16.25" x 5.75" x 4" (41.3 x 14 x 10 cm) - (H x W x D) - Shipping 21" x 10.5" x 9.75" (53 x 27 x 25 cm) Options Remote Temperature Sensor (RTS), HUB 4, HUB 10, MATE, MATE 2 Menu Languages English & Spanish
Use appropriate wire size in accordance with NEC.
* Specifications subject to change without notice.
FREE! Sellers: Add a FREE map to your listings. FREE!
Froo | Froo Cross Sell, Free Cross Sell, Cross promote, Marketing, listing Apps, Apps, ApplicationHurricane Wind Power
2019Corporate America Today2019 Best Off-GridRenewable EnergyProduct Supplier - USAUP TO 50% DISCOUNTSTOP BRANDS
Shipping
We offer Fast shipping on all orders!
Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
Returns
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 14 days from the date you purchased it.
Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.
Thank you for visiting our store! Outback Power Systems
FLEXmax 80
MPPT Charge Controller
The FLEXmax 80 is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Systems. The FLEXmax 80’s innovative MPPT algorithm is both continuous and active, increasing your renewable energy yield up to 30%. Thanks to enhanced cooling, the FLEXmax 80 can operate at its full 80 amp maximum current rating in ambient temperatures as high as 104°F (40°C).
Included in the FLEXmax 80 are all of the features first developed by OutBack Power in the revolutionary MX60, such as support for a wide range of nominal battery voltages and the ability to step-down a high voltage solar array to recharge a low voltage battery. A built-in backlit display shows status information at the touch of a button. Enhanced network communications allow the FLEXmax 80 to be remotely programmed via the optional MATE system display and controller.
The new FLEXmax 80 is the only choice when you demand a high performance, efficient and customizable charge controller for your advanced power PV Array Output by up to 30%
Advanced Continuous Maximum Power Point Tracking Algorithm Full Output Capacity in Ambient Temperatures up to 104°F (40°C) Battery Voltages from 12 VDC to 60 VDC Automatic Battery Voltage Detection at Start Up Fully OutBack Network Integrated and Programmable Programmable Auxiliary Control Output Negative or Positive Ground System Capable Built-in 128 days of Data LoggingFLEXmax™ 80 Specifications* Nominal Battery Voltages12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up) Maximum Output Current 80 amps @ 104° F (40°C) with adjustable current limit Maximum Solar Array STC Nameplate 12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC Systems 7500 Watts NEC Recommended Solar Array STC Nameplate 12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts PV Open Circuit Voltage (VOC) 150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum Standby Power Consumption Less than 1 Watt typical Power Conversion Efficiency 97.5% @ 80 Amps in a 48 VDC System - Typical Charging Regulation Five Stages: Bulk, Absorption, Float, Silent and Equalization Voltage Regulation Set points 10 to 80 VDC user adjustable with password protection Equalization Charging Programmable Voltage Setpoint and Duration - Automatic Termination when completed Battery Temperature Compensation Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell Voltage Step-Down Capability Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input Programmable Auxilary Control Output 12 VDC output signal which can be programmed for different control applications (Maximum of 0.2 amps DC) Status Display 3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total Remote Display and Controller
Optional Mate or Mate2 with RS232 Serial Communications Port
Network Cabeling Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires) Data Logging Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production Hydro Turbine Applications Consult factory for approved Turbines Positive Ground Applications Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications) Operating Temperature Range Minimum -40° to maximum 60° C (Power capacity of the controller is automatically derated when operated above 40° C) Environmental Rating Indoor Type 1 Physical Specifications Conduit Knockouts One 1" (35mm)on the back; One1" (35mm) on the left side; Two 1" (35mm) on the bottom Warranty Standard 5 year Weight - Unit, 12.20 lbs (5.56 kg) - Shipping, 15.75 lbs (7.10 kg) Dimensions - Unit 16.25" x 5.75" x 4" (41.3 x 14 x 10 cm) - (H x W x D) - Shipping 21" x 10.5" x 9.75" (53 x 27 x 25 cm) Options Remote Temperature Sensor (RTS), HUB 4, HUB 10, MATE, MATE 2 Menu Languages English & Spanish
Use appropriate wire size in accordance with NEC.
* Specifications subject to change without notice.
FREE! Sellers: Add a FREE map to your listings. FREE!
Froo | Froo Cross Sell, Free Cross Sell, Cross promote, Marketing, listing Apps, Apps, Application
