Creality Ender 3 Pro Custom 3D PrinterRebuilt and CustomizedSerial #AMSC-230101
Refurbished and Customized Anycubic i3 Mega S 3D Printer by Trinity Custom Technologies, LLC. Unit was completelydisassembled,cleaned, with each part examined and replace if found worn, then the unit was reassembled under exactingstandards with a host ofcustom and enhanced parts. The unit was then tested, calibrated, and then tested again to verifybest operation.
During assembly, all parts were verified to be mounted square and all bolts were properly torqued.
List of Modifications:1. Upgraded Firmware to V1.1.5.2. 3D Touch Auto Leveling system added to unit.3. Hotend nozzle replaced with Micro Swiss Plated Brass nozzle.4. Stock filament guide tubing replaced with Capricorn Bowden PTFE Tubing.5. Stock Fan Duct replaced with 360 airflow design fan duct.6. Stocked Spool holder replaced by Roller style spool holder with built in filament scale connected to Raspberry Pi/OctoPrint system.7. Auto Off switch system with On-Off-Auto front power switch added to unit.8. Bubble Level to verify printer is setting level.9. Replaced Z-Axis Stepper Motor Mounts and coupling for better Z-Axis operation.10 .Both Z-Axis and Y-Axis Belt tensioners replaced with adjustable tensioners.11. Print Bed Die Springs and adjustment wheels replaced with firmer units and larger wheels..12. Custom Cable Chain Guides for X-Axis Hot End cables.13. Y-Axis Print Bed cables moved to prevent breakage.14. Raspberry Pi 4 Model B 4 GB with OctoPrint Command and Control software loaded installed in custom Control Display case. Includes 5 MP Camera, Mount, and ring lighting.
Calibration:
A three step calibration process was used to calibrate the i3 Mega S. First a 20 mm cube is printed with the defaultSteps per mm settings.The measured dimensions of the cube are entered in to a spreadsheet which computes a set oftrial Steps per mm settings. Then a 100 mmCalibration model is printed. Again, the measured dimensions are enteredin to the spreadsheet which computes a refined set ofSteps per mm settings. A third 100 mm Calibration model isprinted and measured to verify the settings.
Using Inland PLA+ Filament printed at 210º C and bed surface temp of 50º C. X-Axis 100 mm printed at 100.03 mm Y-Axis 100 mm printed at 100.03 mm Z-Axis 100 mm printed at 100.05 mm
Extruder: A run of 100 mm of filament used 100 mm of filament.Testing:
Initial testing was performed to verified correct operation of all there axis stepper motors, end stops, extruder, Auto Off switch system, cooling fans, filament sensor, and filament scale. Then the unit was calibrated.
After calibration, the unit was tested for 50 hours of operation printing multiple patterns from both the MicroSD Card and OctoPrint Control system to verify correct operation.OctoPrint Command and Control System:
By using a Raspberry Pi 4 Model B dedicated computer connected to your 3D Printer by a USB Cable, the OctoPrint system provides a web page interface to your printer. Through this interface, you can upload print files, start and stop print operations, verify printer operation, and provide status information including video. This greatly simplifies the control and operation of your 3D Printer.
The OctoPrint System includes:
• Dedicated Computer with case, power supply, and all interface cables mounted to the 3D Printer. • All required software including the Lunix Operating System and OctoPrint system with required plugins and extensions. • Filament Spool Scale and roller. • 5MP Video Camera with case and mount. • Print Bed Lighting with Switch. • OctoEverywhere Internet Portal (Free Version). • Connected to your Home or Office WiFi network. • Sync with your installation of Cura Slicing Software installed on your personal computer.What is all included in the box:
Qty 1 Anycubic i3 Mega S Custom 3D Printer with the above customization.
Qty 1 Power Cord (USA Standard)Qty 1 Side CuttersQty 1 Nozzle BrushQty 1 Glue StickQty 1 ScrapperQty 1 Set Allen WrenchesQty 1 7 mm WrenchQty 1 Z-Axis Dual Stepper Motor Calibration Guide.Qty 1 8GB SD Card for Printer’s SD slot with sample G-code for Items to Print. (3DBenchy, Test-Dog, xyzCalibration_cube, and PLA_Temperature_Tower)Qty 1 USB to SD Card ReaderQty 1 16GB USB Thumb Drive with Anycublic standard instructions and Trouble Shooting guides, plus copy of the Trinity Custom Technologies Calibration Sheet and Instructions for setting up Cura Slicing software. Also sheet of recommended filament brands and other supplies.Qty 1 Spare Hotend assembly.Qty 1 USB cable.Qty 1 Spare Endstop Switch,Qty 1 Nozzle Cleaner.
Qty 1 Spool of Black PLA+ Filament, 1Kg.Please check for more information.
