Netgear Bundle - 1 ProSafe GS408EPP Switch & 4 ProSafe WAC720 WIreless AP.
- This would be a great "starter" kit with 4WAC720 dual-band wireless access points, and 1 GS408EPP L2/L3 switch with 8 PoE ports. All you need is the Cat5 (or better) network cables that support PoE.- Because the switch has 8 PoE enabled ports, you can also connect PoE cameras (instead of using battery powered WiFi cameras) or other devices that are PoE enabled.
*** Sold only as a bundle and not individually.
- I have owned these since new and they are 100% functional. Three of them were online and supporting my small office and the 4th was a "spare" and is still "new in the box" (except for testing and firmware upgrade recently).I tested them all and made sure they are at the latest Netgear firmware and reset them to factory defaults
GS408EPP - Easy-Mount 8-Port PoE+ Gigabit Ethernet Plus Switch- The NETGEAR Smart Managed Plus features a unique Virtually Anywhere™ mounting system that allows to install more PoE+ ports exactly where you need them. The unique mounting system allows you to put the Easy-Mount Switch up in the ceiling, strapped to a pole, or mounted under a desk or tabletop, making it the perfect switch for deploying Wireless APs, Pan/Tilt/Zoom and fixed IP Cameras, VoIP Phones, access-limited security door locks or any other IoT PoE-powered devices.Should you decide to rack mount the GS408EPP switch, you can save space by installing two (2) switches in just a single 1U slot as all connections (power and Ethernet) are located on the front side, allowing back-to-back installation.As a member of the NETGEAR Smart Managed Plus family, the GS408EPP also includes a full set of software features such as traffic prioritization, VLANs, QoS, Port Trunking/Link Aggregation and PoE power allocation.The GS408EPP also features Energy Efficient Ethernet (IEEE 802.3az) for maximum power savings.- 8 PoE/PoE+ ports (124W total PoE power budget) to power up AC Wave 2 Access Points, Pan/Tilt/Zoom Security Cameras, VoIP/video conferencing phones, security door locks, etc.- Whisper quiet 26.9dB acoustics when operating at 25°C (77°F), well below normal offices ambient background noise.- Internal power supply to eliminate power brick (100-240v AC 50-60Hz. 3A Max).
WAC720 - ProSAFE Business 2 x 2 Dual Band Wireless-AC Access Point- The NETGEAR® ProSAFE® WAC720 is a high performance 2 x 2 business class dual band 802.11ac wireless Access Point (AP) that can support an aggregate through-put of up to 1.2 Gbps (300 Mbps for 2.4 GHz and 867 Mbps 802.11ac for 5 GHz).Equipped with industry unique capability of Quad Mode management, allowing user to flexibly switch access point from one management mode to another without complexity.Quad Mode management enables WAC720 to operate in standalone, ensemble, controller, and Business central modes, based on the required deployment scenario.- Deploy wireless coverage over large areas with point-to-point and point-to-multipoint bridging via Wireless Distribution System (WDS)- PoE powered, no external power brick needed (there are no power bricks included).- Standalone mode uses the built-in "Ensemble" mode that will join up to 10 AP for client roaming seamlessly (this is not mesh).- Up to 16 SSID (8 per band) and joining tagged VLANs for each SSID.- Internal antennas factory-optimized (5/6dBi) for maximum RF performance.- SMA reverse antenna take-offs enable optional accessory antenna attachment for 2.4GHz and/or 5GHz operationsfor extended range (I am including several high-gain antenna in case they are needed)
The full specifications for the GS408EPP and the WAC720 can still be found on the Netgear site.
Included in the bundle:- One GS408EPP switch, rack mount ears and 120v AC power cord- Four WAC720 Access Points, three matching 2-peice ceiling / wall mounting plates and one matching 1-peice ceiling / wall mounting plate- Eight 12dBi high-gain mono-pole external antenna (white)- Ten 5dBi mono-pole external antenna- Four 9dBi di-pole external antenna