TESTING & COSMETIC NOTES:
This is a USED WORKING item in GOOD cosmetic condition that IS THOROUGHLY TESTED and is GUARANTEED WORKING
The unit has been reset to the factory default settings. See console log below.
COMPONENTS INCLUDED IN THIS sale:• (1) - RUCKUS ICX 7150-48P 48-PORT POE MANAGED ETHERNET NETWORK SWITCH ICX7150-48P-4X1G
• (1) - POWER CABLE
REPLACEMENT or MONEY BACK GUARANTEE:When you receive a Guaranteed item from OC Depot, it should perform as described. In the rare situation that this is not the case, we will send a replacement upon safe return of the original item within 30 days of receiving the item. If a replacement is not available we will honor the terms of our Money-Back Guarantee.
ADDITIONAL INFORMATION:The following is the Console Log from this item:
Ruckus Wireless Bootloader: 10.1.15T225 (Jan 30 2019 - 23:08:47 -0800)
Booted from partition 2
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-48 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0xa
device 0 offset 0xbfe00, size 0x200
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Secondary
NAND read: device 0 offset 0x4000000, size 0x2000000
33554432 bytes read: OK
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90d
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fa14
Data Size: 2401258 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: ac67d750
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90d
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fa14
Data Size: 2401258 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: ac67d750
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x704a07b4
Data Size: 27682307 Bytes = 26.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: 011bd5e3
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x7049e55c
Data Size: 8607 Bytes = 8.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6fc9a37b
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x7049e55c to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end 6500d19e
Starting kernel ...
Mounting file system...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
Processing packages from secondary partition
Installed packages are up to date
Starting up system statistics daemon...
Starting systatsd done
Starting up health monitor daemon...
Log Level 7: Daemonized systatsd
Systatsd Logging Env is not set, initializing loglevel to: 7
Setting connection to systemlogger
Starting hmond done
Hmond Logging Env is not set, initializing loglelvel to: I
Setting connection to systemlogger
Backup is fine
Kernel crashdump is disabled.
FIPS reset is enable.
Removing startup config & backup
Removing stacking.boot
Remodma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000,
warm_mem_len: 0xb00000
ving SSL_CERT_FILE
Removing SSH_RSA_HOSTKEY_FILE
Removing SSH_DSA_HOSTKEY_FILE
Creating TUN device
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the FastIron.
USER=root
boot_partition=sec_partition
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=c8:03:f5:22:7e:07?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT NOT DISABLED
platform type 94
OS>
Loaded Image SPR08090d from Sec Built on (UTC): Mon Sep 23 07:08:29 2019
Enabling Console Logging
Applying factory defaults..
INFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
Hotplugger Daemon Initialized ..
External USB disk is not mounted or plugged in.
set_board_level: gi_board_type = 120[ 67.130349] linux-kernel-bde: map phys ra
nge 0x3200000-0x3240000 to 0xb0b2f000-0xb0b6f000
[ 67.293832] linux-kernel-bde: map phys range 0x20000000-0x20040000 to 0xb0aef
000-0xb0b2f000
[ 67.395439] linux-kernel-bde: map phys range 0x20800000-0x20840000 to 0xb0aaf
000-0xb0aef000
[ 67.576632] linux-kernel-bde: map phys range 0x88100000-0x90100000 to 0xa8aaf
000-0xb0aaf000
DMA pool size: 134217728
PHY Reset De-asserted
sw_pp_sdk_init:136 ToR init
SOC unit 0 attached to PCI device BCM56160_B0
SOC unit 1 attached to PCI device BCM56160_B0
Firmware version from File: 2.1.1
Pre Parsing Config Data ...
INFO: empty config data in the primary area, try to read from backup
INFO: empty config data in the backup area also
Done with Pre-allocating nexthop id's for Unicast & Openflow
Warning: This operation would close all existing SSH connection.
Creating RSA key pair, please wait...
Parsing Config Data ...
INFO: empty config data in the primary area, try to read from backup
INFO: empty config data in the backup area also
Going to sleep forever...
Successfully notified stack role 'none' to hmond
PS 1, Internal Power supply detected.
PS 1, Internal Power supply is up.
PoE: Stack unit 1 PS 1, Internal Power supply with 370000 mwatts capacity is up
PoE Info: Adding new 54V capacity of 370000 mW, total capacity is 370000, total
free capacity is 370000
System initialization completed...console going online.
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Sep 23 2019 at 00:00:25 labeled as SPR08090d
(32539748 bytes) from Secondary SPR08090d.bin (UFI)
SW: Version 08.0.90dT213
Compressed Secondary Boot Code size = 786944, Version:10.1.15T225 (mnz1011
5)
Compiled on Thu Jan 31 07:08:55 2019
HW: Stackable ICX7150-48-POE
UNIT 1: SL 1: ICX7150-48P-4X1G POE 48-port Management Module
Serial #:FEC3828R0E0
Software Package: ICX7150_BASE_L3_SOFT_PACKAGE
Current License: 4X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
UNIT 1: SL 3: ICX7150-4X10GF 4-port 40G Module
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 17 second(s)
The system started at 00:04:46 GMT+00 Sat Jan 01 2000
The system : started=cold start
Press Enter key to login
Creating certificate, please wait...
SSL Client Certificate is successfully created
Press Enter key to login
PoE Info: PoE module 1 of Unit 1 on ports 1/1/1 to 1/1/48 detected. Initializing
....
2000 log entries of PoE Event Trace Log Buffer is allocated on unit 1 for unit 1
PoE Event Trace Logging enabled for unit 1
RSA Key pair is successfully created
ICX7150-48P RouterPoE Info: PoE module 1 of Unit 1 initialization is done.
User Access Verification
Please Enter Login Name: super
Please Enter Password:
User login successful.
User super login successful with default password. Please change the password.
Enter the new password for user super : Please Click Here to Visit Our StoreSearchBy31 - 278167 | Loc: I52 | L: Rob |T: | PM: Nick | QTY: 0| Plan: 20% - NET of FEES |22.00"x18.00"x5.00"20.00lbs |Start: $0.00 | BIN: $299.99 | |2026-06-26 ||Computers/Tablets & Networking::Enterprise Networking, Servers::Switches & Hubs::Network Switches
