Release Film for Anycubic Mono X / X 6K / X2 / 6Ks / M3 Plus (260 × 175 mm) – FEP or PFA (nFEP)Pre-cut release film for the Anycubic Mono X / X 6K / X2 / 6Ks / M3 Plus, cut to 260 × 175 mm so it drops straight into the vat frame with no measuring, no cutting and no wasted roll. Sheets are cut from fresh factory rolls, packed flat with protective liners, and shipped from our Gold Coast store.Choose your film type from the Film type option above — FEP or PFA (nFEP). Not sure which to pick? See the comparison below and in the product images.Changing your film is a ten-minute job — follow our Installation Guide.Which film should I choose? FEP (5 pack) — the proven everyday film. Standard fluoropolymer release film. Clear, affordable and forgiving. Five sheets per pack so you always have spares on the shelf. PFA nFEP (2 pack) — lower peel force, longer life. nFEP is a PFA-based film with a lower surface tension than FEP, so models release with less peel force. Gentler on fine supports, quieter, and it lasts noticeably longer between changes. Two sheets per pack. FEP PFA (nFEP) Sheets per pack 5 2 Thickness 0.15 mm 0.15 mm Light transmission ≥ 95% ≥ 95% Model release Good Excellent Service life Standard (typically 20–30 prints) Long (typically 2–3× FEP) Finish Clear Clear Key Features Cut to fit: exact vat-frame size for the listed printers, no trimming needed. High durability: resists resin, UV and repeated peel cycles. Excellent light transmission: even curing across the whole build plate. Easy model release: low surface energy so prints lift cleanly off the film. Packed flat: protective liners both sides, no creases or scratches. Specifications Dimensions: 260 × 175 mm Compatibility: Anycubic Mono X / X 6K / X2 / 6Ks / M3 Plus Film types: FEP (5 pack) · PFA nFEP (2 pack) Thickness: FEP and PFA (nFEP) 0.15 mm Light transmittance: ≥ 95% (FEP / PFA (nFEP)) Temperature resistance: FEP 205 °C continuous / 260 °C peak Brand: NovaFEP release film, stocked and cut by 3docity Compatibility is based on the vat-frame film size. If your printer isn't listed but uses the same size, it will fit — ask us if unsure. Release Film for Anycubic Mono X / X 6K / X2 / 6Ks / M3 Plus (260 × 175 mm) – FEP or PFA (nFEP)
Pre-cut release film for the Anycubic Mono X / X 6K / X2 / 6Ks / M3 Plus, cut to 260 × 175 mm so it drops straight into the vat frame with no measuring, no cutting and no wasted roll. Sheets are cut from fresh factory rolls, packed flat with protective liners, and shipped from our Gold Coast store.
Choose your film type from the Film type option above — FEP or PFA (nFEP). Not sure which to pick? See the comparison below and in the product images.
Changing your film is a ten-minute job — follow our Installation Guide.
Which film should I choose?
- FEP (5 pack) — the proven everyday film. Standard fluoropolymer release film. Clear, affordable and forgiving. Five sheets per pack so you always have spares on the shelf.
- PFA nFEP (2 pack) — lower peel force, longer life. nFEP is a PFA-based film with a lower surface tension than FEP, so models release with less peel force. Gentler on fine supports, quieter, and it lasts noticeably longer between changes. Two sheets per pack.
FEPPFA (nFEP)Sheets per pack52Thickness0.15 mm0.15 mmLight transmission≥ 95%≥ 95%Model releaseGoodExcellentService lifeStandard (typically 20–30 prints)Long (typically 2–3× FEP)FinishClearClearKey Features
- Cut to fit: exact vat-frame size for the listed printers, no trimming needed.
- High durability: resists resin, UV and repeated peel cycles.
- Excellent light transmission: even curing across the whole build plate.
- Easy model release: low surface energy so prints lift cleanly off the film.
- Packed flat: protective liners both sides, no creases or 260 × 175 mm
- Compatibility: Anycubic Mono X / X 6K / X2 / 6Ks / M3 Plus
- Film types: FEP (5 pack) · PFA nFEP (2 pack)
- Thickness: FEP and PFA (nFEP) 0.15 mm
- Light transmittance: ≥ 95% (FEP / PFA (nFEP))
- Temperature resistance: FEP 205 °C continuous / 260 °C peak
- Brand: NovaFEP release film, stocked and cut by 3docity
Compatibility is based on the vat-frame film size. If your printer isn't listed but uses the same size, it will fit — ask us if unsure.
× × ×
Shipping info
Click the Shipping & Payments tab above the listing description for more info
Click the Shipping & Payments tab above the listing description for more info!
Additional delivery notes
PICK UP OPTION
Sorry, our items are NOT available for pick-up.
PAYMENT
Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.
We accept payment via All Major Credit Cards (Visa, Mastercard, AMEX, Discover), Google Pay, PayPal, & Apple Pay (on mobile & App).
Thank you for shopping with us on !
Additional Information
No additional information at this time
Ask seller a question
You might also like Bed Leveling Silicone Spring Spacer 50W 24V Heater Cartridge Generic GT2-6mm Idler Pulley 5mm inner bore E3D High Precision Heater Cartridges Contact
To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.
Ask seller a question
© 3docity
Shipping & Payments
Click the Shipping & Payments tab above the listing description for more info
Payment
Accepted Payment Methods
Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.
We accept payment via All Major Credit Cards (Visa, Mastercard, AMEX, Discover), Google Pay, PayPal, & Apple Pay (on mobile & App).
Thank you for shopping with us on !
Returns
Returns are accepted
Items must be returned within 30 days of the sale ending
Seller will pay for return shipping.
integration by
