Bigtreetech Manta E3EZ V1.0 & 5x EZ2209 For Ender 3,5/CR10Kit Include: 1x Manta E3EZ Control Board 5x TMC2209 EZ Kit Include: 1x Manta E3EZ Control Board 5x TMC2209 EZ 1x CB1 V2.2 [Depending on your selection] CB1/CM4 is not included, you can source CB1 here: or Source CM4 from official raspberry pi distributor (Support Klipper only). Note: Please ensure you have enough clearance for the CB1/CM4 sd card when closing up case, for Ender 3 Pro you will be break the one the support tab. Please refer to more information/video overview. Note: CM4/CB1 are mounted using M2 bolt (not the M2.5 included in heat sink for CB1). (M2x10) BIGTREETECH MANTA E3EZ V1.0 is a motherboard developed by the 3D printing team of Shenzhen Bigtree Technology Co. for ender 3 running Klipper. At the same time, this motherboard is the first one launched by BIGTREETECH that incorporates “Manta” technology (which means inserting CB1 core board directly on the motherboard), “EZ” technology (which means using the latest EZ drivers). Simply plug in the CB1 core board and EZ driver on the motherboard to upgrade your ender 3 printer to a Klipper printer. Running Klipper in this way will greatly eliminates the need for extensive cabling between the motherboard and the Raspberry Pi, and saves space in the case. More Information: Install Overview: User Manual: Pin out: Klipper Firmware Config Example: Printed Bracket (ender 3 v2): Printed Mount (Ender 5): Feature: 32bit 64MHz ARM Cortex-M0+ series STM32G0B1RE MCU. TPS5450-5A power supply chip supports DC12/24V power input, current output rated at 5A max continuous and 6A max instantaneous, sufficient power supply for Raspberry Pi. The thermistor circuit is protected to prevent MCU damage from shorted heated bed and heater cartridge connections. MCU firmware can be upgraded via SD card, or use DFU via Klipper’s make flash command. BTB connectors are adopted between the motherboard and core board, allowing the choice of other core board solutions in addition to CM4. Onboard SPI and UART mode of EZ driver, which can be used directly without a jumper. Onboard DIAG pin, easily configurable with jumpers. Support power loss recovery, filament runout sensor, auto power-off, BLTouch, RGB, etc. High-efficiency MOSFET for less heat generation. Replaceable fuse for easy maintenance. Onboard SPI interface for connecting acceleration sensor to enable Klipper’s input shaping. The temperature sensor interface adopts a high-precision pull-up resistor. Each motor driver module can select the corresponding motor voltage by jumper caps The motor power supply supports up to 56V, and for the larger voltage when using EZ5160, an isolation chip is used to protect the main control from shorts Bigtreetech Manta E3EZ V1.0 & 5x EZ2209 For Ender 3,5/CR10

All Prices include GST. Message us if require a tax invoice.

Kit Include:

• 1x Manta E3EZ Control Board
  
• 5x TMC2209 EZ

 

Kit Include:

• 1x Manta E3EZ Control Board
  
• 5x TMC2209 EZ
• 1x CB1 V2.2

[Depending on your selection]

CB1/CM4 is not included, you can source CB1 here: [link removed by ] or Source CM4 from official raspberry pi distributor (Support Klipper only).

Note: Please ensure you have enough clearance for the CB1/CM4 sd card when closing up case, for Ender 3 Pro you will be break the one the support tab. Please refer to more information/video overview. 

Note: CM4/CB1 are mounted using M2 bolt (not the M2.5 included in heat sink for CB1). (M2x10)

BIGTREETECH MANTA E3EZ V1.0 is a motherboard developed by the 3D printing team of Shenzhen Bigtree Technology Co. for ender 3 running Klipper. At the same time, this motherboard is the first one launched by BIGTREETECH that incorporates “Manta” technology (which means inserting CB1 core board directly on the motherboard), “EZ” technology (which means using the latest EZ drivers). Simply plug in the CB1 core board and EZ driver on the motherboard to upgrade your ender 3 printer to a Klipper printer. Running Klipper in this way will greatly eliminates the need for extensive cabling between the motherboard and the Raspberry Pi, and saves space in the case. 

More Information: [link removed by ]

Install Manual: [link removed by ]

Pin out: [link removed by ]

Klipper Firmware Config Example: [link removed by ]

Printed Bracket (ender 3 v2): [link removed by ]

Printed Mount (Ender 64MHz ARM Cortex-M0+ series STM32G0B1RE MCU.

TPS5450-5A power supply chip supports DC12/24V power input, current output rated at 5A max continuous and 6A max instantaneous, sufficient power supply for Raspberry Pi.

The thermistor circuit is protected to prevent MCU damage from shorted heated bed and heater cartridge connections.

MCU firmware can be upgraded via SD card, or use DFU via Klipper’s make flash command.

BTB connectors are adopted between the motherboard and core board, allowing the choice of other core board solutions in addition to CM4.

Onboard SPI and UART mode of EZ driver, which can be uséd directly without a jumper.

Onboard DIAG pin, easily configurable with jumpers.

Support power loss recovery, filament runout sensor, auto power-off, BLTouch, RGB, etc.

High-efficiency MOSFET for less heat generation.

Replaceable fuse for easy maintenance.

Onboard SPI interface for connecting acceleration sensor to enable Klipper’s input shaping.

The temperature sensor interface adopts a high-precision pull-up resistor.

Each motor driver module can select the corresponding motor voltage by jumper caps

The motor power supply supports up to 56V, and for the larger voltage when using EZ5160, an isolation chip is uséd to protect the main control from shorts

HAVE A QUESTION OR CONCERN?

If you need more information regarding this item, please message us or check on original manfuacturers websites.

DREMC STORE back our products and pride ourselves, not only in quality but in genuine products. Please do not hesitate to reach out to us. We stock the largest range of 3D Printer Spares Parts, from Manufacturer such as E3D-Online, Creality, Slice Engineering, Bondtech, Micro Swiss, LDO Motors, Bigtreetech, Trianglelabs to name a few.

We are the largest Australia Creality Spare Part Distributors based in Brisbane, we stock over 200 SKUs Creality Printers spares parts. Our website store.dremc.com.au for latest stock list and accurate real time stock counter, no hidden stock levels.

Do you need bulk spare parts or DREMC / Polymaker filament discount? Message us now if you require B2B/Educational payment terms.

Please check out our response to see what others are saying about us.

× × × × × × × × × × × ×
Tell a friend Visit store Watch now Postage info

Click the Postage tab above the listing description for more info

Click the Postage tab above the listing description for more info!

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYING VIA PAYPAL/CARD

Please refer to Checkout for available payment method.

Price include GST. Message us if require a tax invoice.

Additional Information

No additional information at this time

Ask seller a question

You might also like BIGTREETECH SKR MINI E3 V3.0 32 Bit Control Board for Ender 3 Series Ender 5 Official Creality CR-6 Series (CR-6 SE, CR-6 Max, CR-10 Smart) Control Mainboard Trianglelab CR6 SE Titanium alloy Bi-Metal Heat break For CR-6 SE Ender 3 Neo Creality Ceramic Bi-Metal Hotend for Ender 3 S1 CR10 Smart Pro Sprite Extruder Contact

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© DREMC STORE

Postage

Click the Postage tab above the listing description for more info

Returns

Returns are accepted

Items must be returned within 30 days of the sale ending

Buyer will pay for return shipping.

integration by