All Extrusions are M5 Threaded Tapped for your Ball screw nut fixing and dismounting requires professional tools or done by professional stuffs!
Never rotate the ball screw nut over the ball screw end! This is very important as if the ball bearings come off the ball nut the ball screw will not work properly and you will void any warranty!
ULTIMATE Bee
Bulk-Man 3D is the largest wholesaler of Open Source CNC parts worldwide. By producing or sourcing parts directly from the factory, we eliminate the “middle man”, and in doing so, we can provide
the best wholesale price direct to the many CNC owners and members of the community approached us requesting a linear rail solution for their machine at an affordable price, our technicians worked hard researching different
options available and ways we can improve on existing designs. The result of the project was the QueenBee Pro CNC Machine.
Carrying on the tradition of community engagement, CNC owners and members wanted more, our technicians went back to the drawing board researching more improvements based on community
input, the resulting machine is the ULTIMATE Bee CNC Machine.
The ULTIMATE Bee mainly distinguishes itself from the first design, the QueenBee PRO, by having Ball Screws as a transmission system instead of the traditional ACME Lead Screw. The Ball
Screw has high-efficiency levels, delivering more torque to the motor when compared to an ACME Lead Screw used in the QueenBee PRO.
Compatible Material for Cutting/Milling/Engraving: Aluminium / Hard Wood / Soft Wood / Oak / Plexi Glass / Delrin / HDPE / Foam.
Workable Dimensions(mm):
Frame Size
X-Axis
Y-Axis
Z-Axis
500x500mm
273mm
262mm
180mm
500x750mm
273mm
512mm
180mm
750x750mm
523mm
512mm
180mm
750x1000mm
523mm
762mm
180mm
1000x1000mm
773mm
762mm
180mm
1000x1500mm
773mm
1262mm
180mm
1500x1500mm
1273mm
1262mm
Recommended Waste Board Dimensions(mm):
Frame Size
Width
Length
500x500mm
262mm
180mm
500x750mm
512mm
180mm
750x750mm
512mm
180mm
750x1000mm
762mm
180mm
1000x1000mm
762mm
180mm
1000x1500mm
1262mm
180mm
1500x1500mm
1262mm
180mm
'ULTIMATE Bee' Features
After many hours of research and prototyping and also getting response from the community, we worked on creating the ULTIMATE Bee.The ULTIMATE Beehas many features over previous CNC
designs and our team has once again brought an innovating machine to overperform others.
Some upgrades from the QueenBee PRO to the ULTIMATE Bee include:
Precision laser cut 1.5mm rubber gaskets are used on all Ball Nut mounting brackets to allow for easy
alignment while maintaining a ridged and secure join to the gantry plates.
The Gasket aids in the building by compensating for any minor misalignment as well as acting to absorb
vibrations during operation (essential in a more ridged drive system).
There are many benefits in using Ball Screws, such as high efficiency and reversibility, backlash elimination,
high stiffness, high lead accuracy, and many other advantages. Compared with the contact thread lead screws,
a Ball Screw adds balls between the nut and screw. The sliding friction of the conventional screw is thus
replaced by the rolling motion of the balls.
The ULTIMATE Bee drive system has been upgraded to SFS1210 and SFU1204 ball screws and ball nuts. The
10mm pitch SFS1210 is used on all axis giving a noticeable increase in speed while maintaining the ability to be
accurate and with measurable repeatability greater than or equal to 0.01mm. Using the Spark-Concepts xPRO
V5 the calculated resolution of the Y, A and X-axis of the ULTIMATE Bee is 0.00625mm at 1/8th micro-stepping.
The Z-axis SFU1204 Ball Screws have a 4mm pitch so the Z calculated resolution is 0.0025mm.
Ball Screw Resolution vs Microstepping Table:
Micro Stepping
SFU1204 – 4mm Pitch
SFS1210 – 10mm Pitch
Full
0.02mm
0.05mm
44563
0.01mm
0.025mm
44565
0.005mm
0.0125mm
44569
0.0025mm
0.00625mm
44577
0.00125mm
choice means no more broken bits or spindles falling into stock when powering off.
The 2040 Extrusion on the rear of the X-Axis has been replaced with a 4040 to allow for improved cable
management and rigidity.
By adding a 4040 extrusion to the back of a C-Beam Extrusion, the X-Axis is braced with a stronger support.
All plates have been completely redesigned to incorporate better cable management, mounting sensors and
switches, and allowing for more adaptive integrated applications.
All of the main plates are made with thick 10mm aluminium. All surfaces where bearing carriages are mounted
have been machined flat to provide a smooth surface for easy and accurate Linear Rails