TESTING & COSMETIC NOTES:
This is a USED WORKING item in GOOD cosmetic condition that IS THOROUGHLY TESTED and is GUARANTEED WORKING
The unit has been reset to the factory default settings. See console log below.
COMPONENTS INCLUDED IN THIS sale:• (1) - DELL EMC S3148P POWERSWITCH 48-PORT ETHERNET POE+ L3 MANAGED NETWORK SWITCH E06W
• (2) - DELL 1100W POWER SUPPLY
• (1) - RACKMOUNT RAIL KIT
REPLACEMENT or MONEY BACK GUARANTEE:When you receive a Guaranteed item from OC Depot, it should perform as described. In the rare situation that this is not the case, we will send a replacement upon safe return of the original item within 30 days of receiving the item. If a replacement is not available we will honor the terms of our Money-Back Guarantee.
ADDITIONAL INFORMATION:U-Boot 2012.10(Dell EMC) (Nov 08 2019 - 18:20:23)
Boot strap=00000a54 board_type=00000002
Uboot is running in (Mt Augusta)
DRAM: 2 GiB
WARNING: Caches not enabled
I2C :Ready
cpld: val=00
NAND: cs 0 dev_id word 0 2c380026
Micron MT29F8G08ABABA, blocks per lun: 800 lun count: 1
dumping inand[cs=0] addr[DFE80008]
ONFI info: device 1024MB, page 4096B, oobsize 224B, block 512KB,
col-addr 2, row-addr 3, 8-bit
Found strap type 0x2 strap page 0x2
REG_ACC_CONTROL c1040010 spare_area_bytes 10 ecc_level 4 eccbytes 7 steps 8
REG_CONFIG 48252300
512 KiB blocks, 4 KiB pages, 16B OOB, 8-bit
NAND: user oob per page: 3757154418 bytes (8 steps)
NAND: chipsize 1024 MiB
In: serial
Out: serial
Err: serial
arm_clk=1000MHz, axi_clk=499MHz, apb_clk=124MHz, arm_periph_clk=500MHz
Net: Registering eth
et0: phyaddr(0x1) id2(0xf) bcmiproc_eth-0
Hit Esc key to interrupt autoboot: 0
Booting PRIMARY configuration...
boot device : flash
file name : systema (Dell EMC Networking OS system://A
Partition)
Erasing Nand...
Erasing at 0x100000 -- 100% complete.
Writing to Nand... done
Booting Dell EMC Networking OS image
off 0x2700000 addr 0x6fffff10 siz 44e4e4
## Booting kernel from Legacy Image at 70000000 ...
Image Name: netbsd
Created: 1970-01-01 0:00:00 UTC
Image Type: ARM NetBSD Kernel Image (gzip compressed)
Data Size: 4514722 Bytes
Load Address: 00100000
Entry Point: 00100000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Transferring control to NetBSD stage-2 loader (at address 00100000) ...
@ABC12-DEFG01H1IJKLMYZ!
Muboot arg = 0xdfe7ffe0, 0, 0xdff8d688, 0xdff8d688
NetBSD/evbarm (bcm53xx) booting ...
initarm: Configuring system, CLIDR=1110000003 CTR=0x83338003 PMUSERSR=0
[ Kernel symbol table missing! ]
Loaded initial symtab at 0x806244ac, strtab at 0x80666cdc, # entries 17010
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Dell Networking OS Release 9.14(2.14)
NetBSD 7.1.2 (S3100) #1: Fri Apr 8 14:29:32 PDT 2022
total memory = 2048 MB
avail memory = 1979 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 1000 MHz Cortex-A9 r3p0 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 4-way L1 VIPT Instruction cache
cpu0: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
iprockbde0 at mainbus0 IPROC dev_rev_id=0x1b340,Dev=b340,rev=0001
Created a iProc BCM switch device BA=0x48000000 IRQ=194 device=0xb340
BCM Bus Space mem Handle = 0x80542c80
_dma_pbase = 0x66000000
DMA VBASE:0xe7000000 DMA PBASE:66000000
armperiph0 at mainbus0
arml2cc0 at armperiph0: ARM PL310 r3p2 L2 Cache Controller (disabled)
arml2cc0: cache enabled
armgic0 at armperiph0: Generic Interrupt Controller, 256 sources (245 valid)
armgic0: 32 Priorities, 224 SPIs, 5 PPIs, 16 SGIs
a9tmr0 at armperiph0: A9 Global 64-bit Timer (500 MHz)
a9tmr0: interrupting on irq 27
bcmcca0 at mainbus0: BCM56340 (Rev A0)
bcmcca0: interrupting at irq 123
com0 at bcmcca0 channel 0: ns16550a, working fifo
com0: console
com1 at bcmcca0 channel 1: ns16550a, working fifo
bcmgpio0 at bcmcca0 gpio addr:0xff000060
gpio0 at bcmgpio0: 32 pins
bcmccb0 at mainbus0
bcmmdio0 at bcmccb0: MDIO bus @ 2 MHz
bcmrng0 at bcmccb0: Random Number Generator (512 bit FIFO)
bcmi2c0 at bcmccb0 port 1
iic0 at bcmi2c0: I2C bus
i2cctl0 at iic0
tmp75x0 at iic0 addr 0x49
tmp75x0: unable to register with sysmon
tmp75x1 at iic0 addr 0x4a
tmp75x1: unable to register with sysmon
stmrtc0 at iic0 addr 0x68
cpldx0 at iic0 addr 0x28CPLD attched at 28
sfpx0 at iic0 addr 0x50: SFP eeprom at addr 0x50
sfpx1 at iic0 addr 0x51: SFP eeprom at addr 0x51
bcmi2c1 at bcmccb0 port 2
iic1 at bcmi2c1: I2C bus
i2cctl1 at iic1
s2eeprom0 at iic1 addr 0x50: AT24Cxx compatible EEPROM
s2eeprom1 at iic1 addr 0x51: AT24Cxx compatible EEPROM
s2eeprom2 at iic1 addr 0x52: AT24Cxx compatible EEPROM
s2eeprom3 at iic1 addr 0x52: AT24Cxx compatible EEPROM
ltc4215x0 at iic1 addr 0x40LTC4215 - HOTSWAP CONTROLLER (MB) 0
psufanctlx0 at iic1 addr 0x58 - PSU FAN controller (MB) 0
psufanctlx1 at iic1 addr 0x58 - PSU FAN controller (MB) 1
max6639x0 at iic1 addr 0x2cFan controller attached at 0x2c
WRITE SUCCESS[r-0x4]:0x10 - 0
bcmeth0 at bcmccb0 port 0: Gigabit Ethernet Controller
bcmeth0: interrupting on irq 234
bcmeth0: Ethernet address 00:01:02:03:04:05
brgphy0 at bcmeth0 phy 1: BCM54616S 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FD
X, auto
bcmeth1 at bcmccb0 port 1: Gigabit Ethernet Controller
bcmeth1: interrupting on irq 235
bcmeth1: Ethernet address 00:01:02:03:04:07
OUI 0x001be9 model 0x0011 rev 2 at bcmeth1 phy 1 not configured
bcmnand0 at bcmccb0: nand revision 0x80000601
onfinand0 at bcmnand0: ONFI NAND Flash
onfinand_read_parameter_page:570 crc 0x510f integrity 0X510F
onfinand0: vendor: MICRON, model: MT29F8G08ABABAWP
onfinand0: page size: 4096 bytes, spare size: 224 bytes, block size: 524288 byte
s
onfinand0: LUN size: 2048 blocks, LUNs: 1, total storage size: 1024 MB
1G nand is present
onfinand0: column cycles: 2, row cycles: 3, width: x8
Found BBT table for chip
flash0 at onfinand0: NAND flash partition size 1024 KB, offset 0, read only
flash0: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash1 at onfinand0: NAND flash partition size 512 KB, offset 0x100000
flash1: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash2 at onfinand0: NAND flash partition size 256 KB, offset 0x180000, read onl
y
flash2: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash3 at onfinand0: NAND flash partition size 256 KB, offset 0x1c0000, read onl
y
flash3: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash4 at onfinand0: NAND flash partition size 512 KB, offset 0x200000, read onl
y
flash4: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash7 at onfinand0: NAND flash partition size 28 MB, offset 0x400000, read only
flash7: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash8 at onfinand0: NAND flash partition size 1024 KB, offset 0x2000000
flash8: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash9 at onfinand0: NAND flash partition size 1024 KB, offset 0x2100000
flash9: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash10 at onfinand0: NAND flash partition size 1024 KB, offset 0x2200000
flash10: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash11 at onfinand0: NAND flash partition size 2048 KB, offset 0x2300000
flash11: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash12 at onfinand0: NAND flash partition size 2048 KB, offset 0x2500000, read
only
flash12: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash13 at onfinand0: NAND flash partition size 128 MB, offset 0x2700000
flash13: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash14 at onfinand0: NAND flash partition size 128 MB, offset 0xa700000
flash14: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
flash15 at onfinand0: NAND flash partition size 728 MB, offset 0x12700000
flash15: erase size 512 KB, page size 4096 bytes, write size 4096 bytes
ld0 at flash15 child attached
bcmusb0 at bcmccb0
ohci0 at bcmusb0: OHCI USB controller
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at bcmusb0: ECHI USB controller
ehci0: companion controller, 2 ports each: ohci0
usb1 at ehci0: USB revision 2.0
bcmusb0: interrupting on irq 117
ld0: 728 MB, 740 cyl, 32 head, 63 sec, 512 bytes/sect x 1492991 sectors
ld0: sector size : 512, number of sectors : 1492991uhub0 at usb0: Broadcom OHCI
root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1 at usb1: Broadcom EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
netdisk:netdisk attach invoked..
f10mc pseudo-device
platform pseudo-device
WRITE SUCCESS[r-0x4]:0x10 - 0x10
max6639: smbus timeout enabled
i2c_cpld_recovery_thread created
crshntfy pseudo-device
s3100_diag as pseudo-device getting attached
Broadcom Device Enumerator (nbsd_ubde)
0: Interrupt mode CMICm
connect secondary isr
KNET: Pseudo device attach
bcnp pseudo-device
bcmw pseudo-device
bcmwstk pseudo-device
f10logger as pseudo-device getting attached
bfd pseudo-device
boot device:
root on md0a dumps on netdisk0a
WARNING: clock gained 1640 days
route: writing to routing socket: File exists
0.1: File exists: gateway 127.0.c14be808
c14be808
Size of ReleaseImage is 44620159 Bytes
RELEASE IMAGE HEADER DATA :
--------------------------
Release Image SW Image Count : 4
Release Image Major-Version : 9
Release Image Minor Version : 14
Release Image Maint Version : 2
Release Image Patch-Version : 14
Release Image Header Size : 140
Release Image Data Size : 44620019
Release Image Platform Type : 27
Release Image Product Name : FTOS-S3100
Release Image Checksum Value : 0xfc1cf978
Release Image Header Checksum: 0x1e44377f
Release Image Create Year : 2022
Release Image Create Month : 4
Release Image Create Date : 8
Release Image Create Hour : 14
Release Image Create Minute : 44
Release Image Create Second : 25
SOFTWARE IMAGE HEADER DATA :
----------------------------
Software Image[1] Major Version : 9
Software Image[1] Minor Version : 14
Software Image[1] Maint Version : 2
Software Image[1] Patch Version : 14
Software Image[1] Image type : 2
Software Image[1] Header Size : 100
Software Image[1] Img Data Size : 4514804
Software Image[1] Img Orig Size : 4514804
Software Image[1] Family Code : cp
Software Image[1] Img file Name : CPRPLP-RPM-AP-9.14.2.14.bin
Software Image[1] Hdr Checksum : 0xd9886090
Software Image[1] Data Checksum : 0xf5a238d1
SOFTWARE IMAGE HEADER DATA :
----------------------------
Software Image[2] Major Version : 9
Software Image[2] Minor Version : 14
Software Image[2] Maint Version : 2
Software Image[2] Patch Version : 14
Software Image[2] Image type : 2
Software Image[2] Header Size : 100
Software Image[2] Img Data Size : 23680066
Software Image[2] Img Orig Size : 119377936
Software Image[2] Family Code : nbsdpcprplp
Software Image[2] Img file Name : NBSDPCPRPLP-RPM-AP-9.14.2.14.bin
Software Image[2] Hdr Checksum : 0x5f0475d9
Software Image[2] Data Checksum : 0x725b68c1
SOFTWARE IMAGE HEADER DATA :
----------------------------
Software Image[3] Major Version : 9
Software Image[3] Minor Version : 14
Software Image[3] Maint Version : 2
Software Image[3] Patch Version : 14
Software Image[3] Image type : 2
Software Image[3] Header Size : 100
Software Image[3] Img Data Size : 15793865
Software Image[3] Img Orig Size : 64051216
Software Image[3] Family Code : nbsdlibcp
Software Image[3] Img file Name : NBSDLIBCP-RPM-AP-9.14.2.14.bin
Software Image[3] Hdr Checksum : 0x338ad268
Software Image[3] Data Checksum : 0x862d3877
SOFTWARE IMAGE HEADER DATA :
----------------------------
Software Image[4] Major Version : 5
Software Image[4] Minor Version : 2
Software Image[4] Maint Version : 1
Software Image[4] Patch Version : 10
Software Image[4] Image type : 1
Software Image[4] Header Size : 100
Software Image[4] Img Data Size : 630884
Software Image[4] Img Orig Size : 630884
Software Image[4] Family Code : cp
Software Image[4] Img file Name : CPRPLP-RPM-BT-5.2.1.10.bin
Software Image[4] Hdr Checksum : 0xdb69f9d
Software Image[4] Data Checksum : 0x80374659
0
Partitioning 1G flash parition flash15...Pass!
Starting Dell EMC Networking OS
STACK: master on f4:8e:38:16:57:17 (1 cpu, 1 unit)
STACK: attach 1 unit on 1 cpu
Oct 5 17:24:20 %S3148P:1 %POLLMGR-2-USER_FLASH_STATE: USB flash disk missing in
'usbflash:'
Oct 5 17:24:21 %STKUNIT1-M:CP %RAM-6-ELECTION_ROLE: Stack-unit 1 is transitioni
ng to Management Stack-unit.
..........Oct 5 17:24:29 %STKUNIT1-M:CP %CRYPTO-5-FIPS_SELF_TEST_PASSED: [sysd]
FIPS crypto module self-test passed
Oct 5 17:24:29 %STKUNIT1-M:CP %CHMGR-5-STACKUNIT_DETECTED: stack-unit 1 present
Oct 5 17:24:34 %STKUNIT1-M:CP %CHMGR-5-LPM_CONFIG: Applying the default IPv6 LP
M partition config
Oct 5 17:24:36 %STKUNIT1-M:CP %CHMGR-5-CHECKIN: Checkin from stack-unit 1 (type
S3148P, 54 ports)
Oct 5 17:24:37 %STKUNIT1-M:CP %CHMGR-4-TEMP_STATUS_CHANGE: Unit 1 temperature
state changed to 0 (Current temperature 40C).
Oct 5 17:24:37 %S3148P:1 %CHMGR-5-FAN_SPEED_CHANGE: Fan speed changed to 40 % o
f the full speed
Oct 5 17:24:37 %STKUNIT1-M:CP %CHMGR-5-FANTRAY_INSERTED: Fan tray 1 of Unit 1 i
s inserted
Oct 5 17:24:37 %STKUNIT1-M:CP %CHMGR-5-PSU_FAN_STATUS: Fan 1 in PSU 1 of Unit 1
is up
Oct 5 17:24:37 %STKUNIT1-M:CP %CHMGR-1-PSU_FAN_STATUS: Fan 1 in PSU 2 of Unit 1
is down
..Oct 5 17:24:38 %STKUNIT1-M:CP %CHMGR-5-STACKUNIT_UP: stack-unit 1 is up
Oct 5 17:24:39 %STKUNIT1-M:CP %CHMGR-2-SYSTEM_READY: System ready
Oct 5 17:25:05 %STKUNIT1-M:CP %RAM-5-STACKUNIT_STATE: Stack-unit 1 is in Active
State.
Oct 5 17:25:18 %STKUNIT1-M:CP %CHMGR-5-PEM_INSERTED: Power entry module 1 of un
it 1 is inserted
Oct 5 17:25:19 %STKUNIT1-M:CP %CHMGR-0-PS_UP: Power supply 1 in unit 1 is up
Oct 5 17:25:19 %STKUNIT1-M:CP %CHMGR-5-PEM_INSERTED: Power entry module 2 of un
it 1 is inserted
Oct 5 17:25:19 %STKUNIT1-M:CP %CHMGR-0-PS_DOWN: Major alarm: Power supply 2 in
unit 1 is down
Oct 5 17:25:19 %STKUNIT1-M:CP %CHMGR-5-MODULE_INSERTED: SFP Plus module has bee
n inserted in stack-unit 1 optional slot 1
Oct 5 17:25:28 %STKUNIT1-M:CP %SYS-5-CONFIG_LOAD: Loading configuration file
Oct 5 17:25:30 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 2/1
Oct 5 17:25:30 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 3/1
Oct 5 17:25:30 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 4/1
Oct 5 17:25:30 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 5/1
Oct 5 17:25:30 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 6/1
Oct 5 17:25:31 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 7/1
Oct 5 17:25:33 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 8/1
Oct 5 17:25:36 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 9/1
Oct 5 17:25:37 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 10/1
Oct 5 17:25:37 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 11/1
Oct 5 17:25:37 %STKUNIT1-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state
to down: Ma 12/1
Oct 5 17:25:37 %STKUNIT1-M:CP />R: Required SMARTSCRIPTS Package(>= 9.7) not found, SupportAssist uninstalled.
Oct 5 17:25:37 %STKUNIT1-M:CP %CLI-6-SECURE_CLI_NOT_ENABLED: CLI security mode
not enabled
Oct 5 17:25:37 %STKUNIT1-M:CP %SEC-5-LOGIN_SUCCESS: Login successful on console
DellEMC> Please Click Here to Visit Our StoreSearchBy37 - 280348 | Loc: Z164 | L: Mitchell |T: | PM: Nick | QTY: 0| Plan: L FREESHIP - 20LBS |22.00"x21.00"x5.00"26.00lbs |Start: $0.00 | BIN: $229.99 | |2026-10-06 ||Computers/Tablets & Networking::Enterprise Networking, Servers::Switches & Hubs::Network Switches
