Product description The video showcases the product in use.The video guides you through product setup.The video shows the product being unpacked. POE Over Coax EOC Converter

LINOVISION EOC&POE converter transmits IP Video & Audio & Data & POE Power over coax cable.Upgrade traditional analogue video surveillance system to IP surveillance system without replacing coaxial cable. It is working with POE IP camera, POE Wi-FiAP, VoIPphone, etc.Plug-and-play.Configuration free.

Unique Features Compared with Competitors Industrial design

Industrial design, with built-in heat sink Ensure super reliability and hassle-free transmission.

POE power + Data transmission

It can Provide power to remote POE device with max. 30W and no local DC power adapter is required. （Note: The POE OUT Port only support PoE Mode A）

Transmission Performance

Compatible to IEEE802.3af/IEEE802.3at POE protocol, max21W POE load capacity in 100m(330ft), or 11W POE load capacity in 300m(1000ft).

DIN-Rail Installation

DIN-Rail Installation. Plug-and-play, configuration free, makes installation simplest. Small design (3.1"x2.0"x0.9") and light weight.

General EOC Applications

Important Notification: For multiple PoE over coax cables application in one system, it is highly recommended to use EOC-Switch KIT(ASIN: B0BMG63JZ6) to avoid potential signal interference.

1 Over Twisted Pair Cable 2 Application for Non-POE 3 For VoIPPhone 4 For DC12V Device 5 Long Reach PoE Application in Elevator

It can transmit POE power and IP data over coaxial or twist pair cable. One passive EOC-transmitter will be put inside the elevator cart to feed camera or signal board, and one EOC-receiver will be in the control room, powered by POE switch/POE injector/POE NVR.

1 Waterproof Enclosure 2 FAQ1 3 FAQ2

• 【PoE & IP OVER COAX CONVERTER】LINOVISION’s POE IP Over Coax converter can be used to upgrade analog system to IP surveillance system while using existing coaxial cable. Compatible with RG59, RG6, RG11 cables. Supports POE standards 802.3af (PoE) and 802.3at (PoE+). EOC Receiver MUST be powered by POE switch or POE injector while Transmitter should be connected with POE devices or NON-POE devices
• 【POE & IP OVER TWIST PAIR CONVERTER】 Each pair of EOC(Ethernet over Coax) Converter is equipped with 2 BNC to Twist Pair connectors, which enables POE over Twist Pair transmission. 100Mbps bandwidth over 330ft regular twist pair cables while 10Mbps over 1485ft for both POE or NON-POE devices. It’s ideal for the CCTV system in elevator cart.
• 【INDUSTRIAL DESIGN WITH BUILT-IN HEAT SINK】Industrial design, with built-in heat sink, ensure super reliability and hassle free transmission. Indoor use ONLY. Plug-and-play, configuration free, makes installation simplest. Small design (3.1"x2.0"x0.9") and light weight.
• 【POINT TO POINT CONNECTION ONLY】Act as MoCA (Multimedia over Coax) in point-to-point connection, transmit video/audio/data/control signal over coaxial cable, so as being used with twist pair. EOC Receiver should be powered by POE switch or POE injector while Transmitter should be connected with POE devices or NON-POE devices.
• 【PLUG-N-PLAY】The installation is very easy and no configuration or expertise is required. Just plug the EOC Receiver to an POE switch or POE injector, and then connect to EOC Transmitter via Coaxial cable or twist pair cable. IP camera or VoIP phone will then get POE power and data transmission from this EOC Transmitter
• 【IMPORTANT NOTIFICATION】 For multiple PoE over coax cables application in one system, it is highly recommended to use EOC-Switch KIT(ASIN: B0BMG63JZ6) to avoid potential signal interference.