Product DescriptionAbout this item

• 🌐What Is CPE977: 5.8G wifi bridge point to point outdoor CPE977 is designed with digital tube display, supports point to point/point to multipoint pairing. Can be paired by dialing without entering the GUI, avoiding complicated setup procedures and saving a lot of time.
• 🌐1200Mbps Gigabit Wifi Bridge: Extend wifi/network from building to building, transmission rate between 2 point to point wireless bridges up to 1200Mbps. The network speed up to 433Mbps. Transmission/receiver bridge support automatically connecting network, WDS network mode & video network dual compatible, provides stronger anti-interference ability and better stability.
• 🌐5KM/3.1Miles Transmission Distance: With built in 16 dBi integrated directional antennas, the ethernet bridge extends networks up to 5 KM/3.1Miles long distance. This ULNA wireless bridge is widely used in daily life. Ideal for warehouse, garden, barn, office, shop, or garage next to your home to extend the network.
• 🌐Plug and play: The point to point wireless bridge outdoor is powered by a 24V Poe adapter(included). The wifi bridges are pre-configured, just connect the Poe power supply to achieve automatic pairing of the 2 bridges. Not only extend home's network to the second building but also for surveillance & security cameras.
• 🌐5.8G Technology & IP65 Waterproof: The wireless bridge using 5.8G IEEE 802.11ac single-band wireless transmission technology, provides better anti-interference performance and compatibility, stronger anti-adjacent channel interference than 2.4G traditional CPE. This point to point wireless bridge outdoor is IP65 waterproof, dustproof, cold-proof, and heat-resistant, it’s a good choice for outdoor.

Note:Products with electrical plugs are designed for use in the US. Outlets and voltage differ internationally and this product may require an adapter or converter for use in your destination. Please check compatibility before purchasing.50M-5KM Long Range Wireless Transmission

Application Case:

Easy to set up, just be sure both units are set to the same channel. I set up the transmitter in the house and aimed it at the receiver 600 feet away, behind one of the windows in our barn. After a minute or so they were communicating with full bars. Been up and running about a month. I tested my speed in the house at 355Mbps and I get 325Mbps. So far so good.

Easy to use:

1. Unbox everything

2. Switch one unit to A and one unit to B

3. Connect the POE to each unit using the Ethernet cable and plug the POE in

4. Wait for them to power up, about 2 min

5. For 5.8 gh Use the tiny reset button to click through until you get a channel with a letter. A,B,C… Then on the other unit do the same. Both units need to be on the same channel

6. You should see them sync

7. Place the unit you designated B in step 2 above at the existing WiFi point and the unit designated A at the location you are trying to establish extended WiFi

8. Plug at cable from your router to the POE then to the unit

9. At the far end plug a cable in the unit, then to the POE then another cable from the POE to your new router

10. Enjoy

Wireless Bridge High Speed Supports Point-to-Point and Point-to-Multipoint

Switch Master-slave Bridge

wireless bridge ethernet switches between master and slave bridges via the A-B button, with A representing the master bridge and B representing the slave bridge. Note that in point-to-multipoint applications, take one of the bridges as A and the other bridges as B. Then set them all to the same channel number to complete the point-to-multipoint

1 Gigabit Port

The gigabit wifi bridge has 1 100Mbps and 1000Mbps ports, both of which can accept a 24V PoE power supply, recommended to connect a gigabit port, and the CAT 5e network cable can be used as a power cable to supply power and transmit data. DC power supply is not recommended. Tip: only the PoE port supplies power

Features

16dBi antenna

Transmission distance up to 5 km

Dialing to set the transmitter and receiver

Support PC side to modify IP settings

WDS networking mode, video network dual compatibility

Dynamic MIMO power saving mode (DMPS) and automatic power saving transmission (APSD)

Elevator Monitoring Application

Using the poe wifi bridge to transmit surveillance signals in elevator monitoring prevents cable damage and provides stable surveillance images. In addition, the wireless bridge can be quickly installed and easily disassembled for reuse, making it an ideal choice for elevator monitoring

Watchdog Function

Bridge with watchdog function. When the long range wifi bridge communication fails, the corresponding unit will automatically detect and restart, restore network communication by itself

Easy Installation

Use metal ties (included) to secure the high speed wifi bridge to the bracket or hang it on the wall. Tip: Install the 2 wireless bridges facing each other as much as possible, with a clear and unobstructed view, so that the bridge can achieve the best condition. Recommended ULNA Universal Bracket (ASIN: B0BCNZFNTD)

Clear and Stable Video Transmission