Product DescriptionAbout this item

• CPE820 Gigabit wireless WiFi bridge is a 5.8G Long Range WiFi Extender Outdoor CPE with a digital tube display. Point-to-point pairing can be done by dialing without having to access the GUI, avoiding the complex setup program, saving much human work and cost, and making the long-range wireless coverage, data transmission, and wireless monitoring simple and professional.
• 1000Mpbs digital display wireless bridge, transmission/receiver automatic networking, support point-to-point, point-to-multipoint, transmission/receiver flexible switching. WDS networking mode, video network dual compatible. The transmission speed between 2 bridges max is 1200Mbps. The highest network speed that can be achieved max is 433Mbpss.
• 1Gbps Wireless ethernet bridge conducted deep protocol optimization for wireless video surveillance transmission to ensure high-speed video transmission and smooth video surveillance, and the underlying wireless driver is optimized in-depth, using 5.8G IEEE 802.11ac single-band wireless transmission technology, with stronger anti-interference ability and better stability
• Outdoor wireless bridges adopting low power consumption and high-performance design, the RF index and radiation index are in full compliance with national standards. Supports dynamic MIMO power saving mode (DMPS) and automatic power-saving transmission (APSD), supports 24V POE power supply, is easy to install and deploy, simplifies construction, safe and reliable. Automatically re-pair when power is restored after a power outage.
• Point to point wireless bridge built-in 16dBm directional antenna, maximum 27dBm can automatically power adjustment to adapt to environmental changes, ensuring smooth video regardless of ultra-close distance, transmission distance up to 3km(Barrier-free), actual application distance should be less than 3KM.FCC ID: 2A6EJ-CPE450

Note:Products with electrical plugs are designed for use in the US. Outlets and voltage differ internationally and this product may require an adapter or converter for use in your destination. Please check compatibility before purchasing.

UeeVii CPE820 is a long-distance 5.8G wireless transmission device. It uses wireless communication technology to transmit network data using air as a medium to perform long-distance point-to-point or point-to-multipoint interconnection. The working data link layer realizes the interconnection of local area networks. The transmission distance can reach up to 3km. CPE820 Video Bridge Transmission usually consists of two devices in AP and Client mode respectively. On the Client-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment. CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems, and so on. Point to point extend network WiFi range, extend the network in the house to your barn, garage, church, warehouse, and even neighbor's house through wireless bridge signal transmission. No need to install a new modem and pay for it every month, saving you money.

Package Included:

2 * CPE820 Gigabit Bridge

2 * Gigabit POE Adapter (24V)

2 * Cat 5e Network Cable

2 * Metal Hoop

1 * User Manual

Applications Case

I was looking for a wireless bridge to bring internet connection to my backhouse about 500 feet from the main house, which is too far for wifi range and too long to run the ethernet cable. I connected the adapter to the bridge using the ethernet cable on one end and the other end of the ethernet cable to the main house internet hub. I connected the other adapter to the other bridge using another ethernet cable for the backhouse. I like that the bridges can go very far, up to almost a mile without obstruction, which is ample for my need. Will look to see if the bridge can be connected wirelessly to the hub in the main house.

Helpful Indicator Lights

Change the characters of the digital tube at the bottom of the wireless bridge to modify the pairing signal channel. The steady light state indicates that it is working, and the blinking state indicates that it is being set. The lights on the sideshow the power and LAN connection status, and the signal lights indicate the signal strength of the paired 2 bridges.

Only One 1Gbps Post

The wireless bridge has 1 100Mbps and 1000Mbps RJ45 ports, both of which can accept a 24V PoE power supply, recommended to use the 100M port for power supply, and the gigabit port is directly connected to the network, which will make the network speed better. And the CAT 5e network cable can be used as a power cable to supply power and transmit data. DC power supply is not recommended. The PoE adapter has a PoE port and a LAN port, and only the PoE port supplies power.

Switch Master-slave Bridge

Point wireless bridge switches the master and slave bridges through the A-B button, A represents the master bridge, and B represents the slave bridge. In point-to-multipoint, take one of the bridges as A, and the other bridges as B, and then set them to the same pairing character to complete the point-to-multipoint pairing.

Easy Installation

You can fix the point-to-point bridge on the bracket (ASIN: B09NLLG8MZ) with metal ties, or you can hang it on the wall; 2 wireless bridges are installed face to face as much as possible, with a clear view. It is recommended to purchase the UeeVii Universal Bridge Bracket.

Lane Monitoring Application

Display your courtyard camera, garage camera, and driveway camera images in the monitoring room wirelessly, without digging and burying lines, destroying the road, and saving costs.

Elevator Monitoring Application

Using a wireless bridge to transmit monitoring signals in elevator monitoring can effectively avoid cable damage and obtain stable monitoring images. Wireless bridges are especially important in large projects, where they can be quickly deployed and easily dismantled for reuse.

Network Extension Application

Extend the network in the house to your barn, garage, church, warehouse, even neighbor's house through wireless bridge signal transmission. No need to install a new modem and pay for it every month, saving you money.

More Application ScenariosHow to Access and Setting the Wireless Bridge CPE Through Computer Access:

• Step 1. Use a PoE adapter to power the wireless bridge through a network cable. Pay attention to the "PoE" and "LAN" ports marked on the PoE adapter, and power is supplied by POE instead of a DC power interface.
• Step 2. Use a network cable to connect the CPE "LAN" port, connect the network cable other ends to the PoE Adapter "POE" port, use another network cable to connect to the "LAN" port of the PoE adapter, and connect the other end of the network cable to the computer's "LAN" port.
• Step 3. Find the number of the Wireless Bridge CPE digital display tube. For example, the number is 1 and the CEP is the A master bridge, then the IP of this CPE is 192.168.255.101; if the CPE is the B slave bridge, then the IP address of the CPE is 192.168.255.201.（There is a table corresponding to a number and IP in the manual）
• Step 4. Very important step: Modify your computer's IP address, change your computer's IP address to 192.168.255.xxx(192.168.255.xxx cannot be the same as the IP of the CPE), make your computer's IP and the bridge's IP address be on the same network segment so that you can access them. Please refer to the manual to modify the computer IP address step or Google searches how to modify the computer IP address, it is very simple.
• Step 5. After you modify your computer's IP address, you open the computer browser and enter the IP address of the wireless bridge to access. For example, enter 192.168.255.101 to access.
• Step 6. Enter the account password "admin/admin" to access, and set it after successful access.

Purchase Tips: The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional. If the product is damaged or missing accessories, please let us know to reissue a new set. This CPE cannot directly expand the WiFi range for you. If you have any questions, you can free feel to let us know via Amazon or Email, we will quick response and help you solve your questions.

How to find and change CPE820 WiFi SSID and password?

1. Find the WiFi hotspot password of CPE450, path: Setting-->Wireless--> Name(SSID) and Password.

2. Enter the new SSID and password and save.

On Mar 11, 2024 at 03:20:14 PDT, seller added the following information: