UBB Store

DSLRKIT 250M 8 Ports 6 PoE Switch Injector Passive Power Over Ethernet 52V 90W For Sale

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

DSLRKIT 250M 8 Ports 6 PoE Switch Injector Passive Power Over Ethernet 52V 90W

Price: CN $33.99

Support EXTmode, max Network Cable length to 250 meters

Suitable for Hikvision,DAHUA andother brands with 802.3af/802.3at PoE Powered Devices(PD)

NOTE. When EXTmode enable, the Max bandwidth for the Power Link (PoE) port 1-6network port will be reduced to 10Mbps for each one. Please check your IP CAMERA's bit stream setting. We recommend the value does not over 8Mbps(8192Kbps).

(The up-link is not affected, it will always working at 100Mbps max speed)

8 Ports (2Uplink, 6PoE) 10/100Mbps

Midspan Mode-B Unsolicited Power(4,5+/7,8-)

Compatible IEEE 802.3af/at, Per port Max 50Watt

Wall Mount

52V 75Watt(Max.90W)
(If you switch to the EXTEND mode, the Max allowable Network Cable length will increased to 250 meters. So we use 52V power adapter. This will avoids the power loss over the long distances, and will make sure the PoE IP Camera working.)

(Please select according your device power consumption, in order to ensure device stable running, the total power consumption should not exceed 75watt of the power supply)

If your camera is with word “12V/PoE” as this picture shows, then please select this 48V(or 52V)PoE Switch, do not select 12V PoE Switch.
Because "12V/PoE" means it can offer power supply to camera via 12V DC port or 48V(or 52V) PoE Ethernet port

Gigabit(10/100/1000Mbps) ethernet devicePlease do not access "Power Link port" this will damage your device.

Support EXTEND mode, max Network Cable length to 250 meters.
Midspan Mode-B Unsolicited Power(4,5+/7,8-)
Supports PoE power up to 75W for all PoE ports, Per port Max 52V 1A or 50Watt
Supports PoE IEEE802.3af/at compliant Powered Device (PD)
Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
Full/half duplex transfer mode for each port.

ALL Port: Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with4 pairs UTP Cat5/5e/6 cable。 Port1-6: any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs)

Power LED LED ON: power on. LED OUT: power off GreenLight LINK/ACT LED ON Indicates the port is connected to a network device and has been started LED OFF Indicates that this port is not connected to a network device or has not been started

Standard

IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100BASE-TX Fast Ethernet

IEEE 802.3x Full-Duplex flow control

Protocol

CSMA/CD Ethernet

Data Transfer Rate

Ethernet: 10Mbps (Half Duplex) 20Mbps (Full Duplex)

Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex)

Network Media(Cable)

10Base-T(EXTEND mode): UTP category 5e, 6 cable (maximum 250m) EIA/TIA-568 100Ω STP (maximum 250m)

100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)